Phazeq 500 Phase Adjuster.
Radial Workhorse PhazeQ
Class-A Phase Alignment Module.
The PhazeQ is an analog phase alignment tool designed to work with any 500
series rack, allowing you bring two sound sources together so that the
fundamentals play in sync.
Features
• Dual-function 500 Series module designed for use as a phase alignment
tool with the ability to behave like a very powerful EQ
-
Create exciting new tones that set your recordings apart
• Designed to work with the Radial Workhorse 500 Series rack as well as
other 500 Series racks
-
100 percent discrete Class-A electronics
-
Warm, rich, organic tonal characteristics
• Single phase-shift adjustment control with a 180° polarity reverse for a
full 360° of phase adjustment
-
Switchable low-pass filter with two ranges
• Wet/Dry blend control takes a single source and splits the signal
enabling you to combine the original sound with the phase-shifted signal
-
New type of equalisation with powerful and radical capabilities
-
Expand your creative palette through analogue phase experimentation
• Full-size through-hole 100 percent discrete electronics for optimal
signal transfer
-
All components are hand-selected and hand-mounted
• Road-proven Radial push switches with extra-durable metal outer casings,
rated at over 20,000 cycles
-
Incredibly robust double-layer steel front panel
-
Dual potentiometers with double-up solder points for greater durability
• Potentiometers feature steel casings, steel shafts, and steel retention
nuts
• Gold-plated 15-pin card edge with a double-sided design ensures a
positive connection to the receptacle for improved mating
• Military-spec circuit board with double-sided design and a full ground
plane that assures the lowest possible noise
Specifications
-
Circuit Type:
Discrete component Class-A
-
Frequency Response:
20Hz to 20kHz
-
Dynamic Range:
102dB
-
Noise:
o Dry: -90dB below 0dBu
o Wet: -80dB below 0dBu
-
Maximum Output:
+17dBu
-
THD+N:
o Dry: >0.002 percent at 1kHz (0dB input, 100K load)
o Wet: >0.015 percent at 1kHz (0dB input, 100K load)
-
Intermodulation Distortion:
>0.015 percent at -12dBu out
-
Input Impedance:
3.4K Ohms
-
Output Impedance:
110 Ohms
-
Phase Shift:
o 0° - 180° (frequency dependent)
o 180° - 360° when invert switch is engaged
o Range 1: 300Hz - 3.8kHz
o Range 2: 3kHz - 38kHz
o Dry Signal
o Balanced Output
o +15dBu
-
Power Requirement:
50mA
-
Conditions:
For use in dry locations only between 5°C and 407deg;C
-
Weight:
0.7kg / 1.5lbs
Controls & Connectivity
-
Blend:
Used to control the mix between the original dry signal and the wet
phased effect
-
Phase Shift:
Adjusts the analogue phase shift from 0° to 180° as you rotate the knob
clockwise
-
Invert:
Reverses the polarity of the wet signal to extend the phase shift from
180° to 360°
-
Phaze On:
Bypass with LED indicator lets you switch off the phase shift effect to
compare sounds
-
Filter:
Lets you apply a low-pass filter on the phased signal to focus the
effect on the bass frequencies
-
Shift:
Extends the filter range from 3kHz - 38kHz to 300Hz - 3.8kHz to better
focus the effect of the filter
-
Shift On:
Bypass with LED indicator lets you switch off the filter to compare the
effect it has on the signal path
-
Omniport:
Dry track output used to feed other devices. Available when used with
the Workhorse